Cart
ZAR® Interior Oil Base Poly PRO
A fast set polyurethane for residential and commercial areas.
Currently out of stock. Select another size or find your local dealer.
See Return Policy
Shipping included. Taxes not included.
Regional shipping restrictions may apply.
Not sure how much product you need?
Product Overview
ZAR® Interior Oil Base Poly PRO is a highly effective finishing system trusted by contractors and do-it-yourself customers.
Its short drying time makes it a great choice for busy people who need to get the job done in a day. Through advances in resin technology, ZAR® Interior Oil Base Poly PRO saves time and money while delivering outstanding consistency and control.
Coats: 2 – 3, recommended 3 on floors
Clean Up: Mineral spirits
Coverage: 400 – 500 square feet per gallon
Dry Time: 30 minutes to 1 hour, 2 hour recoat
- Oil base
- Available in gloss, satin, matte
- Application by brush, lambs wool applicator, pad, sprayer
- Self-leveling for a superior finish
- CSI Masterformat® 09 93 23 Interior Polyurethanes
Surfaces
- Wood
- Faux wood
- Plastic
- Fiberglass
- Masonite®
- MDF
- Metal
Videos
Preparation
New Wood
Sand smooth using fine sandpaper and vacuum any sanding dust.* Wipe it clean with a tack cloth or a cloth dampened with paint thinner or mineral spirits, and allow it to dry. If open-grained woods are to be filled, use a filler that does not contain stearates or waxes, such as ZAR® Patch Wood Filler or ZAR® Trowelable Wood Patch.
Old Finishes in Good Condition
Remove all dirt, oil, wax, polish, and grease with turpentine or a suitable solvent.* Sand lightly in the direction of the grain to remove gloss. Wipe it clean with a tack cloth or a cloth dampened with paint thinner or mineral spirits, and allow it to dry.
Old Finishes in Poor Condition, Lacquer or Shellac
Remove completely.* Clean sanding dust with a tack cloth or a cloth dampened with mineral spirits to remove any remnants of dust prior to application and allow it to dry. If the old finish contains wax or stearates, regardless of condition, remove it completely. Sand and remove sanding dust. Test ZAR® Interior Oil Base Poly PRO in an inconspicuous area for compatibility.
Application
Stir thoroughly before and during application. Do not shake! Apply straight from the can. Do not thin. May be applied using a brush, pads, a lambswool applicator or by spray. Apply ZAR® Interior Oil Base Poly PRO in the direction of the grain. Sand lightly between coats. Remove all sanding dust with a vacuum or tack cloth. If more than 24 hours elapses between coats, sand thoroughly and clean. Allow the first coat to dry for up to 2 hours, and succeeding coats for up to 2 hours. Temperature, humidity and film thickness may affect drying time. If, while sanding, sandpaper gums or the surface feels tacky, extend the drying times.
Disposal
Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations.
FAQs
Q: Can ZAR Polyurethanes be used over paint?
A: Our ZAR Polyurethanes are best applied to bare wood or over a cured wood stain. They are not designed for use over paint.
Q: Do I need to sand between coats of ZAR Polyurethane?
A: Sanding is not required, but if desired a light scuff with 220 grit sandpaper can help to promote intercoat adhesion.
Q: Can ZAR Stain or ZAR Polyurethane be applied over a lacquer or shellac?
A: No, a lacquer or shellac must be fully removed.
USAGE STATEMENT: Prior to use, carefully read the product label and follow the directions. For technical information, warnings, cautions, notices, and additional information, download and read the documentation available on this website.
California Residents: Prop 65 WARNING(S)
* WARNING: If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1 – 800-424-LEAD or visit www.epa.gov/lead.