ZAR® Clear Wood Sealer & Natural Toner Base
ZAR® Clear Wood Sealer & Natural Toner Base protects exterior wood surfaces from the effects of rain, sun, and other weather damage. It may be applied to new or old wood that has been left unstained and unpainted, and is ideal for all types of woods including pressure-treated lumber and log cabins. ZAR® Clear Wood Sealer & Natural Toner Base accents the natural grain, texture and color of wood with just one coat. Apply a second coat to deepen the color and bring out a soft sheen.
Clean Up: Soap and water
Coverage: 100 – 400 square feet per gallon
Dry Time: 4 hours, decks 24 hours
- Latex Base
- Transparent, a second coat deepens the color and brings out a soft sheen
- Application by brush, roller, foam pad, applicator pad, sprayer
- Ideal for pressure treated lumber, pine, redwood, cedar, composite decking materials, and other exterior unstained or unpainted wood surfaces such as decks, rails, posts, fencing, gazebos, sheds, wooden shingles, shakes, and log cabins
- CSI Masterformat® 09 93 13 Exterior Deck, Fence, and Siding Finishes
The surface must be clean, dry, and in good condition. Remove all mildew, dirt, dust, loose wood fibers, paint flakes, mill glaze, oil, and grease*. Test the wood for factory treatment by sprinkling a few drops of water on the surface. If the water is readily absorbed into the wood, proceed. If not, do not apply ZAR® Clear Wood Sealer & Natural Toner Base. Wait 1 month and then retest. Repair or replace any loose, cracked or warped boards. All mildew (dark, fuzzy or powdery deposits) must be removed with ZAR® Deck, Fence and Wood Cleaner. Or, use the following solution: one-third cup heavy-duty laundry detergent to 1 quart household bleach to 3 quarts of warm water. Wear protective eye goggles and waterproof gloves when handling the solution. Apply with a scrub brush. Rinse thoroughly and allow it to dry before staining.
For Old Grayed Wood Exposed to UV (sunlight) for More Than 3 Months
Power wash the surface to remove the thin layer of degraded wood and clean surface as above.* Allow the wood to dry thoroughly after power washing before applying ZAR® Clear Wood Sealer & Natural Toner Base.
Apply only when surface and air temperatures are above 50°F and less than 90°F. Do not thin. Stir thoroughly before and during application. Do not apply if rain is expected within 24 hours. Avoid applying in direct sunlight. Apply using a brush, roller, foam pad applicator, or spray. If sprayed, coating should be dry brushed or back rolled for uniform appearance. One coat will protect and beautify the wood while allowing the natural grain to show through. Optional: a second coat may be applied to deepen the color and bring out a soft sheen.
On vertical siding, start at the top on several boards and apply continuously toward the bottom. On horizontal siding, start at one corner on several boards and apply continuously across, breaking at doors, windows and corners. Be sure to maintain a wet edge. Brush out any runs or lap marks.
As a Natural Toner Tint Base
Test the tinted ZAR® Clear Wood Sealer & Natural Toner Base on a sample piece of wood or in an inconspicuous area to determine the final color. When using 2 or more gallons of the same tinted ZAR® Clear Wood Sealer & Natural Toner Base, mix them together to ensure color uniformity.
Areas with harsh exposure to sun, weather or foot traffic will show wear more quickly than other surfaces. If this occurs, clean the affected areas and recoat as necessary.
Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations.
United Gilsonite Laboratories (UGL®) warrants ZAR® Clear Wood Sealer & Natural Toner Base, subject to the limitations set forth herein, that this product, under normal use and proper storage, will be free from defects in material or workmanship and merchantable for a period of three (3) years on Decks and five (5) years on Siding from the original date of purchase. This limited warranty extends to the original consumer purchaser of the product only and is non-transferable. If this product is found to be defective by UGL within the warranty period, you will receive a replacement of the product or, at UGL’s option, a full refund of the purchase price upon presentation of proof of purchase (original sales receipt). This limited warranty excludes failure to apply the product to a properly prepared bare surface in accordance with UGL’s instructions provided with this product. UGL MAKES NO FURTHER EXPRESS WARRANTIES. THIS LIMITED WARRANTY EXCLUDES (1) LABOR AND ALL OTHER COSTS ASSOCIATED WITH THE APPLICATION OR REMOVAL OF THE PRODUCT OR ANY REPLACEMENT PRODUCT, AND (2) ANY INDIRECT, SPECIAL, EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the limitation or exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights and you may also have other legal rights which vary from state to state. To make a warranty claim, please contact (with proof of purchase) the store where you purchased the product or contact UGL directly at 1−800−848−7253 (Consumer Hotline) or by mail at UGL Consumer Inquiry Department, P.O. Box 70, Scranton, PA 18501 – 0070.
USAGE STATEMENT: Prior to use, carefully read the product label and follow the directions. For technical information, warnings, cautions, notices, and additional information, download and read the documentation available on this website.
California Residents: Prop 65 WARNING(S)
* WARNING: If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1 – 800-424-LEAD or visit www.epa.gov/lead.