ZAR® ULTRA Max Floor Rejuvenator

ZAR® ULTRA Max Floor Rejuvenator

ZAR® ULTRA Max Floor Rejuvenator applies easily to restore, rejuvenate and renew the beauty of floors that are dull, scratched or showing signs of wear. Featuring Dual Drying Technology, this modern polyurethane relies on coalescing and oxygen cross-linking to deliver a harder “through cure” in just two hours.

ZAR® ULTRA Max Floor Rejuvenator Application

Quick Overview

ZAR® ULTRA Max Floor Rejuvenator is perfect for restoring worn polyurethane, shellac, lacquer, aluminum oxide coatings, and other factory-finished wood surfaces. It is approved for use with exotic hardwoods like Teak, Brazilian Walnut, and more.

Product Features:

  • Size: 32 ounce
  • Coverage: 200-300 square feet per 32 ounce container
  • Application tools: synthetic applicator pad, painter’s pad, brush
  • Dry time: 2 hours
  • Coats: 2, for greater protection and durability apply an additional coat
  • Recoat: 2 hours

Surfaces

  • Wood

How To / Videos

How to add New Life to Hardwood Floors with ZAR® ULTRA Max Floor Rejuvenator

See more Home Improvement Videos

Downloads

ZAR® Wood Finishing Project Guide

BROCHURE PDF

ZAR® Hardwood Floors Finishing and Refinishing Guide

BROCHURE PDF
DATA SHEET PDF
SDS SHEET PDF

Preparation

Old Finishes in Good Condition
Remove grease, dirt, and wax.* Sand lightly in the direction of the grain to remove any gloss. Do not use steel wool. Vacuum all sanding dust. Wipe clean using a tack cloth or microfiber cloth. If the old finish contains wax or stearates, regardless of condition, remove it completely. Clean dust with a tack cloth or microfiber cloth.


Old Lacquer or Shellac:
Test compatibility in an inconspicuous area. If acceptable, prepare as directed under “Old finishes in Good Condition”.


Old Finishes in Poor Condition, Lacquer or Shellac
Remove completely.* Do not use steel wool. Sand and vacuum all sanding dust. Wipe clean using a tack cloth or microfiber cloth.


Note: To ensure satisfactory results, always prepare a sample or test the product on an inconspicuous area to determine compatibility prior to completing the entire job. Not recommended over waxed or oiled floors. Test for wax by sprinkling a few drops of water on the surface and wait 10 minutes. If the surface turns white, it indicates the presence of wax that must be completely removed. Badly worn floors require a complete refinishing.

Application

Gently rock the container back and forth to mix. Do not shake. Squeeze a liberal amount of ZAR® ULTRA Max Floor Rejuvenator directly on the wood surface in an “S” pattern. Spread evenly in the direction of the wood grain. Work in 4’ x 4’ sections. Work from the furthest part of the room toward the door so you don’t trap yourself in the room. Apply the product in thin coats and avoid puddles. Let it dry for 2 hours. If you would like to apply additional costs, come back and sand it lightly with 150 to 200 grit sandpaper. Vacuum up the dust and apply another coat just like the first. The more coats you apply, the greater the protection.

Disposal

Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations.

USAGE STATEMENT: Prior to use, carefully read the product label and follow the directions. For technical information, warnings, cautions, notices, and additional information, download and read the documentation available on this website.

* WARNING: If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or visit www.epa.gov/lead.